弯曲段壁面冲击发散冷却结构流量系数与冷却效率的实验

为了研究回流燃烧室弯曲段采用冲击发散冷却结构时的流量系数和冷却效率,设计了多种不同几何尺寸的实验件模型,分别对其流量系数和冷却效率进行了实验研究,得出如下结论:①弯曲段冲击发散冷却结构的流量系数较小,一般不会超过0.7.发散孔倾角为40°的流量系数要小于倾角为20°和30°的流量系数,流量系数随着发散孔纵向间距比的增大而减小.②弯曲段冲击发散冷却结构的冷却效率均随着吹风比的增大而增大,其冷却效率要明显高于直板冲击发散冷却结构,且这种差异随着吹风比的增大而逐渐减弱.      

空间真空环境下密封电磁继电器的触点失效研究

密封电磁继电器有其固有的漏率,在应用于空间真空环境下由于气体泄漏使得其内部气体压力逐渐降低,导致继电器的触点在低气压环境下工作失效（负载切换时）。文章选择国产继电器样品对上述机理进行了试验验证,并对继电器内部气体压力与触点电弧失效的规律进行了研究。     

空间电源功率调节技术综述

介绍了空间电源功率调节装置(PCU)的分流调节器(SR),蓄电池的充电控制器(BCR)、放电控制器(BDR)和主误差放大器(MEA)的原理和技术现状。阐述了顺序开关分流调节(S3R)、混合型调节和顺序开关分流串联调节(S4R)三种基本拓扑的工作原理,并对三者进行了性能比较,认为S4R是目前最先进的调节技术。讨论了功率调节装置模块化、智能化和小型化的发展趋势并分析了大功率的功率调节装置研制难点。     

脉冲等离子体推力器羽流预测计算研究

为了能够将脉冲等离子体推力器成功地运用于空间,需对其羽流进行研究。将一维 MHD双温放电模型的计算结果作为入口条件,运用DSMC（Direct Simulation Monte\|Carlo ）／PIC（Particle in Cell）流体混合算法一体化模拟实验室PPT羽流。验证计算显示该模 型具有一体化模拟脉冲等离子体推力器羽流的能力。对不同初始放电能量下的羽流场进行模 拟,给出了离子、中性粒子、电子温度、轴线上质量流率和出口平面返流质量流率的变化情 况。计算结果显示高放电能量下返流量更大,同时中性粒子在返流中所占比例也越大。
     

肋角度和出流孔位置对流动特性的影响

针对带肋和双排出流孔通道,研究了肋角度和出流孔位置对流量系数分布和总压系数分布的影响.研究的肋角度为60°,90°和120°.出流孔分别位于相邻两肋之间距前肋1/4肋距、两肋中间、距后肋1/4肋距.研究表明:不同的肋角度和出流孔位置不改变流量系数和总压系数沿流向的分布规律;流量系数随肋角度增大而增大;60°和120°肋通道中总压系数绝对值接近且小于90°肋通道中的绝对值;两肋之间,出流孔位置靠近下游,将使流量系数增大,总压系数绝对值增大.      

大迎角分离流场在等离子体控制下的特性研究

设计了一种新型的大迎角主动流动控制方法。采用圆锥-圆柱组合体模拟飞行器前体,在靠近圆锥尖端处镶嵌了一对马蹄形单电极介质阻挡放电（single_Dielectric Barrier Discharge SDBD）等离子体激励器,通过风洞实验研究了等离子体激励器在不同状态下对大迎角模型前体的非对称气动载荷的控制作用。实验结果表明,通过控制等离子体激励器的开闭可以使得圆锥-圆柱组合体在大迎角下出现的侧力改变方向。还对通过调节单侧等离子体激励器的激励电压实现圆锥前体侧力系数在正负极值间连续变化的可能性进行了初步的实验探索。     

地球同步轨道高压太阳电池阵充放电效应研究

地球同步轨道(GEO)高压太阳电池阵表面静电放电(ESD)引起二次放电可能导致太阳电池阵永久性短路损坏。文章主要针对GEO高压太阳电池阵充放电效应问题,重点分析了高压太阳电池阵表面ESD和二次放电产生的物理过程,并利用负高压偏置方法开展了GEO高压太阳电池阵表面ESD和二次放电地面模拟试验。试验验证了反转电位梯度电场是导致GEO高压太阳电池阵表面产生ESD的触发因素之一,同时得到了GaAs高压太阳电池阵样品表面产生ESD和二次放电的电压阈值。     

孔间距和前倾角对进出口扩张形气膜孔流量系数的影响(英文)

Discharge coefficients of 3-in-1 hole of three inclination angles and three spacing between holes are presented which described the discharge behavior of a row of holes. The inlet and outlet of the 3-in-1 hole both have a 15° lateral expansion. The flow conditions considered are mainstream turbulence intensities and density ratios of secondary flow to mainstream. The momentum flux ratios varied in the range from 1 to 4. The comparison is made of the discharge coefficients of three shaped holes to find an optimal hole with low flow loss. The results show that the discharge coefficients of 3-in- 1 hole are highest in three shaped holes and therefore this article is focused on the measurements of discharge coefficients of 3-in-1 hole for various geometries and aerodynamic parameters. The measured results of 3-in-1 hole indicate that turbulence intensities, density ratios and momentum flux ratios have weak influence on discharge coefficients for inclination angle of 20°. The high turbulence intensity yields the small discharge coefficients for inclination angle of 45° and 90°. The increased both momentum flux ratios and density ratios lead to the increased discharge coefficients for inclination angle of 45° and 90°. The increased inclination angle causes the rapidly increased discharge coefficients. There is a weak dependence of discharge coefficients on hole pitches.     

红外地球敏感器地面静电放电模拟试验方法研究

 设计了红外地球敏感器的地面模拟卫星静电放电试验方法。对卫星的空间环境以及结构特点的分析结果表明,地球同步静止轨道卫星表面存在静电放电的可能性。通过静电放电试验找到了红外地球敏感器易受干扰的部位并提出了解决措施。     

Operating characteristics of a high radius pre-swirl cooling system

An experimental investigation into pre-swirl effectiveness and receiver hole discharge coefficient characteristics for a high radius injection pre-swirl cooling systems was carried out on a physically representative experimental rig with a 450 mm diameter rotor.The receiver holes and pre-swirl nozzle were located at a radius of 181 mm and 180 mm respectively.The experimental work was mainly conducted at 5 000～12 000 r/min,4 bar absolute pressure and 1.132 kg/s air supply.The maximum air supply temperature was 190 ℃.Pressure and temperature distributions in the pre-swirl system were examined with an emphasis on the velocity effectiveness of the pre-swirl system as a whole and on the discharge coefficients of the rotating 'receiver holes' in the rotor.The results showed that the velocity effectiveness increased with increasing swirl ratio resulting in reduced blade cooling flow temperature.Different seal flow configurations caused very different effectiveness at different speeds,but outflow through the inner and outer seals always gave the highest effectiveness compared other configurations.Increasing the seal flow rate reduced the effectiveness.For the coefficient of discharge,except for the low speed range,it increased with increase in swirl ratio for most speeds.